E-Coating Cost: How to Quote Electrocoating per kg and per m²
November 20, 2026
Quote parts like this from a drawing — try it on our sample. Try the sample drawingFree for 30 days · Unlimited quotes · No credit card required
E-coating, also called electrocoating, cathodic electrodeposition or, in Italy, cataforesi, is a paint process widely used for steel parts that need corrosion protection at a low cost: brackets, frames, sheet metal enclosures, parts for vehicles and machines. The parts are cleaned and pretreated, immersed in a water-based paint bath, coated by an electric current, rinsed and cured in an oven. Because the current drives the paint into recesses and inside sections, the coating reaches places a spray gun cannot.
For a job shop it is almost always an outside process, and it is one of the lines most often underpriced in a quote: the coater's price per kg or per m² goes into the estimate, and everything around it is forgotten. This guide shows how coaters price e-coating, how to convert between per-kg and per-m² prices, and what to add before the line is right. The worked example in EUR prices a batch of brackets.
How e-coaters price the work
Coaters usually quote in one of three ways:
- Per kg of parts. Simple to check on a scale, common for steel parts of similar shape and thickness.
- Per m² of coated surface. Closer to the coater's real cost, because paint, pretreatment and oven time scale with surface, not with weight.
- Per piece or per hanger. For large or awkward parts, or when the number of parts per rack drives the cost.
On top of that come a minimum lot charge, masking of threads, holes and contact surfaces that must stay bare, and sometimes a charge for hanging holes or special racking. Ask for all of them before you quote; the minimum lot charge alone can multiply the price of a small batch.
Converting per kg to per m²
For sheet metal parts, coated on both sides, the surface per kg depends only on the density and the thickness:
- surface per kg (m²/kg) = 2 ÷ (density × thickness)
For carbon steel at the usual 7,850 kg/m³:
| Thickness | Surface per kg | Weight per m² of coated surface |
|---|---|---|
| 1.5 mm | 0.170 m²/kg | 5.89 kg |
| 2 mm | 0.127 m²/kg | 7.85 kg |
| 3 mm | 0.085 m²/kg | 11.78 kg |
| 5 mm | 0.051 m²/kg | 19.63 kg |
| 8 mm | 0.032 m²/kg | 31.40 kg |
The edges are ignored, which is fine for sheet. The table shows the trap in a per-kg price: it is fair only for the thickness it was set for. With an assumed €3.20/m² and €0.45/kg, a 2 mm bracket of 0.6 kg costs €0.24 priced by surface and €0.27 priced by weight, close enough. An 8 mm plate of 4.2 kg costs €0.43 by surface and €1.89 by weight: priced per kg, the thick part pays more than four times what its surface costs to coat. When your parts differ from the coater's typical work, ask for the price per m², or ask which thickness their per-kg price assumes.
The costs around the coater's price
| Line | What it covers |
|---|---|
| Coater's price | Per kg, per m² or per piece, at least the minimum lot charge |
| Masking | Plugs and caps for threads and holes that must stay bare |
| Your uplift | Risk of rework or damage, capital tied up, the coater's lead time |
| Transport | Both ways, per batch |
| Preparation and packing | Parts clean of oil and chips, protected for transport, counted |
| Receiving inspection | Coverage, adhesion and damage checked when the parts come back |
The design of the part matters too. E-coating needs electrical contact and a way to hang the part, so a part without a suitable hole may need a hanging tab or a special hook. Threads coated by mistake must be re-tapped. If the customer wants a powder coat or a wet paint on top, e-coat becomes the primer and the job carries two finishing lines, each priced on its own; see painting cost for fabricated parts. The same structure applies to any outside finish, such as zinc plating.
Worked example: 300 sheet metal brackets
300 brackets in 2 mm steel, 0.6 kg each, with two tapped holes to keep bare. Coated surface: 2 × 0.6 ÷ (7,850 × 0.002) = 0.0764 m² per bracket. The figures are example figures, not market prices: the coater charges €3.20/m² with a €120 minimum lot charge and €0.10 per masking plug; transport is €45 each way; your preparation and packing take 0.5 minutes per part at €45/h; receiving inspection takes 1 hour at €55/h; your uplift on the coater's invoice is 10%.
| Line | Calculation | Cost |
|---|---|---|
| Coating | 300 × 0.0764 m² × €3.20/m² | €73.34 |
| Masking | 300 × 2 plugs × €0.10 | €60.00 |
| Coater's invoice (above the minimum) | €73.34 + €60.00 | €133.34 |
| Uplift | 10% of €133.34 | €13.33 |
| Transport | 2 × €45 | €90.00 |
| Preparation and packing | 300 × 0.5 min × €45/h | €112.50 |
| Receiving inspection | 1 h × €55/h | €55.00 |
| Total | €404.17 |
That is €1.35 per bracket. The coater's price alone was €0.24 per bracket: an estimate that used only that number would have covered less than a fifth of the real cost of the line.
On a batch of 30 brackets the coating and masking come to €13.33, below the €120 minimum lot charge, and the total is €288.25: €9.61 per bracket. For small batches the minimum lot charge is the price, and it is worth asking the coater whether parts can join another customer's run or wait for the next batch.
FAQ: e-coating cost
How is e-coating priced? Coaters quote per kg of parts, per m² of coated surface or per piece, plus a minimum lot charge and masking. Per m² follows the coater's real cost best, because paint, pretreatment and oven time scale with the surface, not with the weight.
How do you convert an e-coating price per kg into a price per m²? For sheet metal coated on both sides, the surface per kg is 2 ÷ (density × thickness). For 2 mm carbon steel at 7,850 kg/m³ that is 0.127 m² per kg, so a price per kg divided by 0.127 gives the equivalent price per m². The conversion only holds for that thickness.
Why does e-coating a small batch cost so much per part? Because of the minimum lot charge, transport and handling, which are paid per batch. In the example in this article 300 brackets cost €1.35 each and 30 brackets cost €9.61 each, although the coater's price per m² is the same.
What should be added to the coater's price in a quote? Masking of threads and holes, your uplift for risk and capital tied up, transport both ways, preparation and packing of the parts, and receiving inspection when they come back. Together they are often worth more than the coating itself.
E-coating and other finishes in QuoteBuddy
QuoteBuddy reads the technical drawing, including the notes, and builds the estimate as separate lines at your own rates. A coating called out on the drawing becomes its own coating operation; QuoteBuddy does not tell e-coating apart from other paints, so the line is priced at the coating rate you set. When coating is not one of your in-house capabilities, it is treated as outsourced: priced with your outsourcing uplift, with an outsourcing handling line once per order, and flagged for review until you confirm the step and enter the supplier's hourly rate. The setup minutes, cycle minutes and hourly rate of an operation line can be edited, so the line can match the coater's real price. See also make or buy for the cost of any outside operation.
You can watch the QuoteBuddy demo video, from technical drawing to quote. To try it on a drawing of your own, start a free 30-day trial.