All articles

Machined From Solid vs Welded: Which Costs Less?

November 17, 2026

Quote parts like this from a drawing — try it on our sample. Try the sample drawingFree for 30 days · Unlimited quotes · No credit card required

"Machined from solid" means the part is cut out of one solid block or bar, with no welds, castings or formed sheet: everything that is not the part becomes chips. In Italian shops it is ricavato dal pieno. The alternative for a bracket, a frame or a housing is usually to cut plates, weld them together and machine only the faces that matter. Customers often draw the part one way without thinking about the other, and the quote is where the difference shows up.

This guide explains what drives the cost of each route, how to compare them on the same part, and the batch size at which one overtakes the other. The worked example in EUR prices a steel bracket both ways, from one piece to twenty-five.

What "machined from solid" costs

  • Material by weight, most of it wasted. You buy a block larger than the part in every direction. The ratio between the weight of the blank and the weight of the finished part, the buy-to-finish ratio, tells you how much you pay to turn into chips. For an L-shaped or ribbed part it is often high; in the example below it is 5.4.
  • Roughing time. Removing that material takes machine time proportional to the volume removed, at the metal removal rate your machine and tooling actually hold in that material.
  • Few fixed costs. One program, one or two setups, no jigs. That is why solid wins on one-offs and prototypes.
  • Predictable quality. No distortion from welding, no weld inspection, no stress relieving, uniform material.

What "welded and machined" costs

  • Less material. Plates cut close to the final shape, bought or cut in-house, with little waste.
  • Fit-up and welding. Tacking, welding, cleaning the welds. On a small part the fit-up is often longer than the welding itself.
  • Distortion and post-machining. Welding moves the part, so faces and holes that matter are machined after welding: a setup and a cycle you would have anyway, plus the stock allowance to correct the distortion.
  • A welding jig for repeatability. Paid once, worthwhile from a few pieces up, and spread over the batch or shown as a one-off line on the quote.
  • Process risks. Weld quality requirements, inspection, sometimes stress relieving; they all belong in the estimate when the drawing asks for them. The welding fabrication cost guide covers them.

Worked example: a steel bracket, solid or welded

An L-shaped bracket in S355 with a gusset: a 200 × 150 × 15 mm base, a 150 × 100 × 15 mm upright and a triangular 80 × 80 × 10 mm gusset. The finished part weighs 5.55 kg. The rates below are example rates, not market prices: machining center €70/h, welding €65/h, inspection €55/h, CAM €60/h; steel bar at €1.40/kg, laser-cut plate at €2.20/kg.

From solid. The upright sits on the base, so the bracket is 115 mm tall and needs a 205 × 155 × 120 mm block, which weighs 29.93 kg: a buy-to-finish ratio of 5.4, and 3,106 cm³ to remove. At an assumed roughing rate of 60 cm³/min that is 51.8 minutes, plus 25 minutes of finishing.

Line, per pieceCalculationCost
Block29.93 kg × €1.40/kg€41.90
Machining76.8 min × €70/h€89.60
Per piece€131.50
Once per batch2 setups of 45 min at €70/h, CAM 1.5 h at €60/h€195.00

Welded and machined. Three laser-cut plates, 5.55 kg net (the stock allowance for distortion is left out for simplicity) at €2.20/kg: €12.21. Fit-up and tacking 12 minutes, 460 mm of fillet weld (2 × 150 mm on the upright, 2 × 80 mm on the gusset) at an assumed 200 mm/min (2.3 minutes), weld cleaning 5 minutes, all at €65/h: €20.91. Post-weld machining of the base and the mounting face, 20 minutes at €70/h: €23.33. Flatness check and inspection, 8 minutes at €55/h: €7.33. Per piece: €63.78. Once per batch: two machining setups and 45 minutes of CAM (€150.00), a welding setup of 20 minutes (€21.67) and a welding jig at an assumed €180: €351.67.

BatchFrom solid, totalPer pieceWelded, totalPer piece
1 piece€326.50€326.50€415.45€415.45
2 pieces€458.00€229.00€479.23€239.62
3 pieces€589.50€196.50€543.01€181.00
5 pieces€852.50€170.50€670.57€134.11
10 pieces€1,510.00€151.00€989.47€98.95
25 pieces€3,482.50€139.30€1,946.17€77.85

For one or two pieces, machining from solid is cheaper: no jig, no welding setup. From three pieces the welded version is cheaper, and at twenty-five it costs about 44% less per piece. The break-even moves with the buy-to-finish ratio: a compact part with little material to remove stays solid for longer; a large open frame becomes welded almost at once.

When the drawing decides for you

The comparison is only open if the drawing allows both. A note such as "machined from solid", "no welding" or a material certificate that must cover the whole part closes it. So do tolerances that welding distortion cannot hold without excessive post-machining, or a part that will be cyclically loaded where a weld would be the weak point. If the drawing is silent and the quantity is right, offering the cheaper route as an alternative, with its conditions written down, is a good way to win the order honestly. A welded version also means a bill of materials to quote: see quoting welded assemblies.

FAQ: machined from solid or welded

What does "machined from solid" mean? That the part is cut entirely out of one solid block or bar of material, without welds, castings or formed sheet. Everything that is not the part is removed as chips. In Italian it is called ricavato dal pieno.

Is it cheaper to machine a part from solid or to weld it? It depends on quantity and on how much material the solid version wastes. Solid has few fixed costs and wins on one-offs and prototypes. Welded has lower material and machining cost per piece but needs fit-up, welding, post-machining and often a jig, so it wins from a few pieces up. In the example in this article the break-even is three pieces.

What is the buy-to-finish ratio? The weight of the raw blank divided by the weight of the finished part. A ratio of 5.4 means that for every kilogram of part you buy 5.4 kg of material and remove 4.4 kg as chips. The higher the ratio, the more a welded or near-net-shape alternative is worth considering.

When should a part not be welded? When the drawing forbids it, when tolerances cannot be held after welding distortion without heavy post-machining, when the material certificate must cover a single piece, or when the part is cyclically loaded and the weld would be the weak point.

Solid and welded parts in QuoteBuddy

QuoteBuddy reads the technical drawing and prices a machined part from its stock: it rounds the blank up to the sizes in your catalog, prices it by weight at your material prices and builds each operation as its own line, with setup kept apart from cycle time and CAM programming on a separate line, at your shop's hourly rates. Weld labour called out on a drawing becomes its own line, from the weld count and length. A multi-part welded assembly is not priced automatically: QuoteBuddy does not model its bill of materials, so the estimate flags it for review and asks you to price the material by hand. Several quantities on one estimate show how the unit price moves with the batch.

You can watch the QuoteBuddy demo video, from technical drawing to quote. To try it on a drawing of your own, start a free 30-day trial.

We use cookies
We use essential cookies to run QuoteBuddy. With your consent, we also use analytics and marketing cookies. Privacy Policy.

UI build: 9a5f2a06cb797e4f7d25d226434db4cb87c72c48