All articles

Nitriding Cost: How to Quote Gas, Plasma and Salt-Bath Work

November 18, 2026

Quote parts like this from a drawing — try it on our sample. Try the sample drawingFree for 30 days · Unlimited quotes · No credit card required

Nitriding hardens the surface of a finished steel part by diffusing nitrogen into it at roughly 400–580 °C, below the temperature at which steel transforms. There is no quench, so the part moves very little, and the result is a hard, wear-resistant skin, typically 600–1,000 HV, over a tough core. Gears, shafts, extruder screws, hydraulic components, dies and molds are nitrided last, after machining and heat treatment, and for most job shops it is an outside operation.

It is hard to price from memory, because the price is not a function of weight alone. Gas, plasma (ion) and salt-bath nitriding are charged differently; the case depth on the drawing changes the furnace hours far more than the weight does; and every lot carries a minimum charge, masking and testing that never show up in a price per kg. This guide shows how heat treaters price nitriding, what drives the cost, the formulas an estimator needs and what to add around the supplier's price. The worked example in EUR prices a batch of shafts.

How heat treaters price nitriding

Heat treaters usually quote in one of three ways:

  • Per kg of parts. The norm for gas and salt-bath work, where many parts share a furnace load, at a rate set for a stated case depth.
  • Per load or per hour of chamber time. Common in plasma nitriding, where a vacuum chamber is filled and run for a set number of hours.
  • Per piece. For dies, molds and long shafts that fill a load on their own.

On top of that come a minimum load charge, masking of the zones that must stay soft (threads, surfaces to be machined afterwards), a case-depth and hardness test on a witness piece, and sometimes a pre-treatment such as stress relief. Ask for all of them before you quote; the minimum load charge alone can multiply the price of a small batch.

What drives the cost

The three common processes differ in time, surface result and charging. The figures are typical ranges, not quotes.

Gas nitridingPlasma (ion) nitridingSalt-bath nitrocarburizing
Temperature500–530 °C400–560 °C560–580 °C
Typical cycle20–80 h8–40 h1–4 h
CaseDiffusion zone plus a compound layer of 5–25 µmSimilar; the compound layer can be reduced or avoidedCompound layer of 10–25 µm, shallow case
MaskingPlating or stop-off paintSimple mechanical coversDifficult

Within a process, four things move the price:

  • Case depth. Furnace hours grow with the square of the depth (see below), so 0.5 mm instead of 0.3 mm on the drawing nearly triples the hold time.
  • Steel grade. Steels alloyed with chromium, molybdenum, aluminum or vanadium, sold as nitriding steels, reach up to about 1,000 HV. Common alloy steels such as 42CrMo4 (the 4140 family, see 4140 alloy steel machining cost) typically reach about 600–750 HV and must be hardened and tempered first.
  • Load density. The furnace runs the same cycle for 50 kg or 500 kg, so small lots and bulky parts cost more per kg.
  • Masking, tests and papers. Each soft zone is a manual step; reports, certificates and approvals add a fixed charge per lot.

Case depth, hold time and the minimum load

Diffusion slows as it goes deeper: at the same temperature the case depth grows roughly with the square root of the hold time. For an estimate, turn it around:

  • relative hold time = (case depth ÷ reference depth)²

Taking 0.2 mm as 1.0:

Case depth0.2 mm0.3 mm0.4 mm0.5 mm0.6 mm
Relative hold time1.02.254.06.259.0

The rule holds for one steel at one temperature, so use it to compare two drawings and ask the treater for the price at each depth.

The second formula is the minimum load. With an assumed rate of €3.40/kg and a minimum load charge of €350 (example figures, not market prices), the minimum applies to every lot under 350 ÷ 3.40 = 103 kg:

Weight of the lot25 kg50 kg100 kg103 kg or more
Effective price€14.00/kg€7.00/kg€3.50/kg€3.40/kg

The costs around the heat treater's price

LineWhat it covers
Heat treater's pricePer kg, per load or per piece, at least the minimum load charge
MaskingPlating or stop-off on threads and zones that must stay soft
Case-depth and hardness testWitness piece or sectioned part, with report
Your upliftRisk of rework or scrap, capital tied up, the treater's lead time
TransportBoth ways, per batch
Preparation and packingParts clean, free of oil and rust, counted and wrapped
Finishing after nitridingPolishing or lapping of the hardened surface
Receiving inspectionHardness, masked zones, dimensions after nitriding

Nitriding moves parts far less than quenching, but not zero: the surface grows by a few micrometers and slender shafts can bend, so stress relief beforehand may be needed. Grinding afterwards removes the hardest part of the case, so leave a lapping allowance or state the case depth after grinding; see cylindrical grinding cost. The structure is the same for any outside heat treatment, covered in heat treatment cost.

Worked example: 200 nitrided shafts

200 shafts in 42CrMo4, hardened and tempered and machined to size, 2.5 kg each (500 kg), nitrided to a 0.3 mm case, with the threaded end kept soft. The figures are example figures, not market prices: the heat treater charges €3.40/kg with a €350 minimum load charge, €0.80 per shaft for masking the thread and €85 per lot for the report; transport is €60 each way; your preparation and packing take 0.8 minutes per part at €45/h; a light polish of the journals takes 1.2 minutes per part at €52/h; receiving inspection takes 1.5 hours at €55/h; your uplift on the treater's invoice is 10%.

LineCalculationCost
Nitriding500 kg × €3.40/kg€1,700.00
Masking200 × €0.80€160.00
Case-depth and hardness reportper lot€85.00
Treater's invoice (above the minimum)€1,700.00 + €160.00 + €85.00€1,945.00
Uplift10% of €1,945.00€194.50
Transport2 × €60€120.00
Preparation and packing200 × 0.8 min × €45/h€120.00
Polish after nitriding200 × 1.2 min × €52/h€208.00
Receiving inspection1.5 h × €55/h€82.50
Total€2,670.00

That is €13.35 per shaft. The price per kg alone was €8.50 per shaft (2.5 kg × €3.40): an estimate that used only that number would have covered less than two thirds of the real cost.

On a batch of 20 shafts (50 kg) the nitriding comes to €170.00, below the €350 minimum, so the treater's invoice is €350.00 + €16.00 + €85.00 = €451.00. Adding uplift €45.10, transport €120.00, preparation €12.00, polish €20.80 and inspection €82.50 gives €731.40: €36.57 per shaft, 2.7 times the cost of the larger batch, with the price per kg covering less than a quarter. For small batches the minimum and the fixed lines are the price; ask whether the shafts can share a load with another customer's parts.

FAQ: nitriding cost

How is nitriding priced? Heat treaters quote per kg of parts for gas and salt-bath nitriding, per load or per hour of chamber time for plasma nitriding and per piece for large parts, plus a minimum load charge, masking and a case-depth test. The case depth matters more than the weight, because the hold time grows with the square of the depth.

How much longer does a deeper nitriding case take? At the same temperature the hold time grows roughly with the square of the case depth. Going from 0.3 mm to 0.5 mm takes about 2.8 times as long, and from 0.2 mm to 0.4 mm about four times.

Why does nitriding a small batch cost so much per part? Because of the minimum load charge, the test report, transport and handling, which are paid per batch. In the example in this article 200 shafts cost €13.35 each and 20 shafts cost €36.57 each, although the rate per kg is the same.

What should be added to the heat treater's price in a quote? Masking of threads and soft zones, a case-depth and hardness test, your uplift for risk and capital tied up, transport both ways, preparation and packing, finishing after nitriding and receiving inspection. In the example in this article they added 57% to the price per kg.

Nitriding in QuoteBuddy

QuoteBuddy reads the technical drawing, including the notes, and builds the estimate as separate lines at your own rates. A heat treatment called out on the drawing, such as a nitriding note with case depth and hardness, becomes its own heat-treatment operation; QuoteBuddy does not tell nitriding apart from other heat treatments, so the line is priced at the heat-treatment rate you set. When heat treatment is not one of your in-house capabilities, it is treated as outsourced: priced with your outsourcing uplift, with an outsourcing handling line once per order, and flagged for review until you confirm the step and enter the supplier's hourly rate. The setup minutes, cycle minutes and hourly rate of an operation line can be edited, so the line can match the heat treater's real price. See also make or buy for the cost of any outside operation.

You can watch the QuoteBuddy demo video, from technical drawing to quote. To try it on a drawing of your own, start a free 30-day trial.

We use cookies
We use essential cookies to run QuoteBuddy. With your consent, we also use analytics and marketing cookies. Privacy Policy.

UI build: 9a5f2a06cb797e4f7d25d226434db4cb87c72c48