All articles

Shot Peening Cost: Quoting Per Piece, Per Hour and Per m²

November 22, 2026

Quote parts like this from a drawing — try it on our sample. Try the sample drawingFree for 30 days · Unlimited quotes · No credit card required

Shot peening bombards a finished metal surface with small round media, usually steel shot, ceramic or glass beads, at a controlled speed. Each impact leaves a small dimple, and together they leave a layer of compressive residual stress a few tenths of a millimeter deep. That layer slows the start of fatigue cracks, so peened gears, springs, shafts, connecting rods and aerospace parts last much longer under cyclic load, and it also helps against stress corrosion. It is a mechanical treatment for strength, not a cleaning process.

For a job shop it is almost always outside work, and it is often quoted as if it were blasting, which is priced per m² to clean or prepare a surface (see sandblasting cost). Peening is sold as a controlled process: intensity and coverage are specified, measured and recorded, and the price follows machine time, setup and verification, not area. A note such as "shot peen to 0.30 mmA, 100% coverage" is badly under-quoted if it is priced like blasting. This guide shows how peening is priced and what to add around the peener's price. The worked example in EUR prices a batch of gears.

How peeners price shot peening

Peeners usually quote in one of three ways:

  • Per piece. Repeat parts with a fixed cycle on a dedicated fixture, such as gears, springs and connecting rods.
  • Per hour of machine or booth time. Small lots, large or awkward parts, nozzle and robot work.
  • Per m². Large surfaces peened with a nozzle; the price follows the area the nozzle covers per hour.

On top of that come setup and intensity verification per order, masking, the Almen strips and report per lot (the strips measure the intensity) and a minimum lot charge. Ask for all of them before you quote; setup and the minimum can multiply the price of a small batch.

What drives the cost

DriverWhat it does to the price
IntensityMeasured as the arc height of an Almen strip, in mmA; higher intensity needs larger shot and more energy per impact, so slower cycles and more media wear
CoverageTime grows with coverage: 200% takes about twice as long as 100%
Geometry and accessFillets, bores and shadowed zones need fixtures, rotating tables or nozzle work, and more handling per part
MaskingThreads, bearing seats and zones that must keep their size are covered by hand or by fixture
Batch sizeSetup and verification are paid per order, so they weigh on small lots
Verification and recordsStrips per lot, coverage checks and a report; stricter approvals cost more
Thin partsPeening one side bends a thin part, so it needs a fixture or both sides peened

Peening and blasting are often confused, and they are priced differently:

Shot peeningBlasting
PurposeFatigue life and stress corrosion resistance, through a compressive layerCleaning, descaling, surface preparation
MediaGraded round media: steel shot, ceramic or glass beadsAngular grit or any abrasive that cleans
ControlIntensity (Almen strips) and coverageVisual cleanliness and roughness
RecordStrips and report per lotRarely
Usually pricedPer piece or per hour, plus setupPer m² or per hour

From machine time to price

  • price per piece = cycle minutes ÷ 60 × hourly rate
  • price per m² = hourly rate ÷ m² peened per hour
  • time at 200% coverage = 2 × time at 100%
  • setup per part = setup cost ÷ batch size

With an assumed rate of €90/h (example figures, not market prices), a 3-minute cycle is €4.50 per gear; a nozzle that peens 1.5 m² per hour is €60.00 per m²; and at 200% coverage the same gear costs €9.00 in machine time. A setup of 2 hours, €180.00, weighs on each part like this:

Batch size1030100300
Setup per part€18.00€6.00€1.80€0.60

The costs around the peener's price

LineWhat it covers
Peener's priceCycle time at the specified intensity and coverage, setup, at least the minimum lot charge
MaskingCaps, tape or fixtures on bores, threads and seats
Strips and reportAlmen strips, coverage check, certificate of conformity
Your upliftRisk of rework or damage, capital tied up, the peener's lead time
TransportBoth ways, per batch
Preparation and packingParts clean, burr-free and dry, counted and kept apart so surfaces are not marked
Receiving inspectionCoverage on a sample, report check, dimensions and distortion

Peening comes after all machining, heat treatment and grinding: grinding afterwards removes the layer you paid for. It also raises roughness a little, which matters for sealing surfaces and for the callouts in surface finish cost. Gears are the classic case; see gear cutting cost.

Worked example: 300 peened gears

300 steel gears, peened on the teeth to 0.30 mmA at 100% coverage, with the bore and keyway masked. The weight does not enter the price. The figures are example figures, not market prices: the peener charges €90/h; setup and intensity verification take 2 hours per order; the cycle is 3.0 minutes per gear; masking takes 0.5 minutes per gear at €36/h; strips and report are €45 per lot; transport is €45 each way; your preparation and packing take 1 minute per part at €45/h; receiving inspection takes 1 hour at €55/h; your uplift on the peener's invoice is 10%.

LineCalculationCost
Setup and intensity verification2 h × €90/h€180.00
Peening300 × 3.0 min × €90/h€1,350.00
Masking300 × 0.5 min × €36/h€90.00
Strips and reportper lot€45.00
Peener's invoice€180.00 + €1,350.00 + €90.00 + €45.00€1,665.00
Uplift10% of €1,665.00€166.50
Transport2 × €45€90.00
Preparation and packing300 × 1 min × €45/h€225.00
Receiving inspection1 h × €55/h€55.00
Total€2,201.50

That is €7.34 per gear. Machine time alone was €4.50 per gear, about three fifths of the real cost: an estimate that used only the cycle would have missed setup and everything around it.

On a batch of 30 gears the peening comes to €135.00 and the masking to €9.00, but setup and strips stay the same: the peener's invoice is €369.00. Adding uplift €36.90, transport €90.00, preparation €22.50 and inspection €55.00 gives €573.40, or €19.11 per gear, 2.6 times as much, with machine time less than a quarter of it. For small batches setup is the price; ask whether the gears can be peened together with another job on the same setup.

Doubling the coverage to 200% on the 300 gears doubles the peening line to €2,700.00, so the invoice becomes €3,015.00 and the total €3,686.50 (uplift €301.50, transport €90.00, preparation €225.00, inspection €55.00): €12.29 per gear instead of €7.34.

FAQ: shot peening cost

How is shot peening priced? Peeners quote per piece for repeat parts, per hour of machine time for small lots and large parts and per m² for large surfaces, plus a setup charge for intensity verification, masking, Almen strips and a report, and a minimum lot charge. The price follows machine time and setup, not weight.

What is the difference in cost between shot peening and sandblasting? They are different processes. Blasting cleans or prepares a surface and is usually priced per m² or per hour. Peening builds a compressive layer for fatigue life, is controlled by intensity and coverage, and is priced per piece or per hour plus setup, verification and a report, which usually makes it more expensive than blasting for the same surface.

How much does higher coverage add to the price? Machine time grows with coverage, so 200% takes about twice as long as 100%. In the example in this article the cycle goes from €4.50 to €9.00 per gear and the total from €7.34 to €12.29 per gear, a rise of 67%.

What should be added to the peener's price in a quote? Masking of bores, threads and seats, Almen strips and a report, your uplift for risk and capital tied up, transport both ways, preparation and packing, and receiving inspection. In the example in this article machine time was €4.50 of the €7.34 cost per gear: the other 39% came from setup and the lines around it.

Shot peening in QuoteBuddy

QuoteBuddy reads the technical drawing, including the notes, and builds the estimate as separate lines at your own rates. A surface treatment called out on the drawing, such as a shot-peening note with intensity and coverage, becomes its own operation; QuoteBuddy does not tell shot peening apart from other surface treatments, so the line is priced at the rate you set. When it is not one of your in-house capabilities, it is treated as outsourced: priced with your outsourcing uplift, with an outsourcing handling line once per order, and flagged for review until you confirm the step and enter the supplier's hourly rate. The setup minutes, cycle minutes and hourly rate of an operation line can be edited, so the line can match the peener's real price. See also make or buy for the cost of any outside operation.

You can watch the QuoteBuddy demo video, from technical drawing to quote. To try it on a drawing of your own, start a free 30-day trial.

We use cookies
We use essential cookies to run QuoteBuddy. With your consent, we also use analytics and marketing cookies. Privacy Policy.

UI build: 9a5f2a06cb797e4f7d25d226434db4cb87c72c48