Phosphating Cost: Quoting Zinc, Manganese and Iron Phosphate
November 21, 2026
Quote parts like this from a drawing — try it on our sample. Try the sample drawingFree for 30 days · Unlimited quotes · No credit card required
Phosphating is a chemical conversion process for steel parts. They are degreased and rinsed, immersed in a hot acid solution of metal phosphates, rinsed again and, for corrosion protection or sliding, oiled. The surface becomes a thin layer of zinc, manganese or iron phosphate that holds oil or paint: crystalline and gray to black with zinc and manganese, finer and iridescent with iron. It is used on fasteners, pins, gears, shafts, springs and stampings: as a base for paint, as protection under oil and, in the manganese version, as a sliding and break-in layer.
For a job shop it is almost always an outside process, and one of the lines most often priced from the wrong number: the supplier's price per kg goes into the estimate and the oil, masking, minimum lot charge, test report and transport are forgotten. A "phosphated" note on a drawing does not say which of the three processes is meant, and they are not priced alike. This guide shows how phosphating is priced, how to convert a price per kg into a price per m² and what to add before the line is right. The worked example in EUR prices a batch of spindles.
How suppliers price phosphating
Suppliers usually quote in one of three ways:
- Per kg of parts. The norm for barrel work: small parts such as pins, fasteners and washers processed together in a barrel.
- Per m² of treated surface. Common for sheet metal and large parts hung on racks, and closer to the supplier's real cost, because chemicals, coating weight and sludge scale with surface.
- Per piece or per rack. For large or awkward parts, or when the number of parts per rack drives the cost.
On top of that come a minimum lot charge, the oil (type and quantity), masking or plugging of zones that must stay bare, a test report (coating weight, salt-spray hours under ISO 9227) and, for hardened steel, a baking step to relieve hydrogen. Ask for all of them before you quote; the minimum lot charge alone can multiply the price of a small batch.
What drives the cost
Zinc, manganese and iron phosphate are three processes with different baths, times and uses, and the price follows. The figures are typical ranges, not quotes.
| Type | Coating weight | Bath and time | Typical use | Cost level |
|---|---|---|---|---|
| Iron phosphate | 0.2–1 g/m² | 40–60 °C, 1–5 min | Paint base on sheet metal | Lowest |
| Zinc phosphate | 1–5 g/m² as paint base; 5–15 g/m² for oiled protection | 45–90 °C, 2–15 min | Under e-coat and powder coat; oiled fasteners and stampings | Middle |
| Manganese phosphate | 10 g/m² and more | 90–98 °C, 10–30 min | Sliding, break-in and anti-galling parts, always oiled | Highest |
Within a type, four things move the price:
- Coating weight. A heavier layer means a longer immersion and more bath chemistry used per m².
- Surface per kg. Slender and thin parts have a lot of surface for their weight: a single price per kg does not fit every part (see below).
- Barrel or rack. Barrels are cheap per part but suit only small, robust parts; racks add handling per piece.
- Preparation and finish. Oily, scaled or rusty parts need extra cleaning or blasting; oil type, wax or dry finish and the test report add to the line.
Black oxide is the neighbor: it adds about 1 µm and almost no dimensional change, and needs oil for corrosion protection. Manganese phosphate is thicker, holds much more oil and suits sliding parts, but grows a few micrometers per surface. The comparison is in black oxide cost.
Converting per kg to per m²
For solid round parts that are long compared to their diameter, the surface per kg depends only on the density and the diameter:
- surface per kg (m²/kg) = 4 ÷ (density × diameter)
For carbon steel at 7,850 kg/m³:
| Diameter | Surface per kg | Weight per m² of surface |
|---|---|---|
| 6 mm | 0.0849 m²/kg | 11.78 kg |
| 10 mm | 0.0510 m²/kg | 19.63 kg |
| 20 mm | 0.0255 m²/kg | 39.25 kg |
| 40 mm | 0.0127 m²/kg | 78.50 kg |
The ends are ignored, which is fine for slender parts; for sheet use 2 ÷ (density × thickness). With an assumed €2.40/kg, a Ø10 mm pin is charged €47.10 per m² and a Ø40 mm shaft €188.40 per m²: priced per kg, the thick part pays four times as much per m² for the same layer. When your parts differ from the supplier's typical work, ask for the price per m², or ask which diameter or thickness the per-kg price assumes.
The costs around the supplier's price
| Line | What it covers |
|---|---|
| Supplier's price | Per kg, per m² or per piece, at least the minimum lot charge |
| Oil and finish | Type of oil, wax or dry finish, if not included |
| Masking | Plugs or caps on seats and holes that must stay bare |
| Baking | Hydrogen relief for hardened parts, if called out |
| Test report | Coating weight, salt-spray hours, certificate of conformity |
| Your uplift | Risk of rework or damage, capital tied up, the supplier's lead time |
| Transport | Both ways, per batch |
| Preparation and packing | Parts free of cutting oil, chips and rust, counted and kept apart |
| Receiving inspection | Appearance, coating on the surfaces that matter, dimensions after the layer |
The layer grows a few micrometers per surface, so ground fits and tight threads need masking or an allowance. Zinc phosphate is also the usual base under cataphoretic coating: when both are on the drawing the job carries two lines, each priced on its own; see e-coating cost. The same structure applies to any outside finish, such as zinc plating.
Worked example: 400 steel spindles
400 spindles in steel, 0.85 kg each (340 kg), manganese phosphate and oil, with one bearing seat per spindle to be capped. The figures are example figures, not market prices: the supplier charges €2.40/kg with a €150 minimum lot charge, €0.35 per masking cap and €45 per lot for the test report; transport is €50 each way; your preparation and packing take 0.6 minutes per part at €45/h; receiving inspection takes 1 hour at €55/h; your uplift on the supplier's invoice is 10%.
| Line | Calculation | Cost |
|---|---|---|
| Phosphating and oil | 340 kg × €2.40/kg | €816.00 |
| Masking | 400 × €0.35 | €140.00 |
| Test report | per lot | €45.00 |
| Supplier's invoice (above the minimum) | €816.00 + €140.00 + €45.00 | €1,001.00 |
| Uplift | 10% of €1,001.00 | €100.10 |
| Transport | 2 × €50 | €100.00 |
| Preparation and packing | 400 × 0.6 min × €45/h | €180.00 |
| Receiving inspection | 1 h × €55/h | €55.00 |
| Total | €1,436.10 |
That is €3.59 per spindle. The price per kg alone was €2.04 per spindle (0.85 kg × €2.40): a little over half of the real cost.
On a batch of 40 spindles (34 kg) the phosphating comes to €81.60, below the €150 minimum lot charge, so the supplier's invoice is €150.00 + €14.00 + €45.00 = €209.00. Adding uplift €20.90, transport €100.00, preparation €18.00 and inspection €55.00 gives €402.90: €10.07 per spindle, 2.8 times as much, with the price per kg covering a fifth. For small batches the minimum is the price; ask whether the spindles can join another customer's run.
FAQ: phosphating cost
How is phosphating priced? Suppliers quote per kg of parts for barrel work, per m² of treated surface for sheet metal and large parts, or per piece or rack, plus a minimum lot charge, oil, masking and a test report. Per m² follows the supplier's real cost best, because chemicals and coating weight scale with surface, not with weight.
Which costs more: zinc, manganese or iron phosphating? Iron phosphate is the cheapest: a short, cool bath and a thin layer, used as a paint base. Zinc phosphate sits in the middle, and manganese phosphate costs the most, because of a hotter bath, a longer immersion and a heavier layer.
Is phosphating cheaper than black oxide? Black oxide is generally the cheaper and thinner finish: about 1 µm with almost no dimensional change. Manganese phosphate is a thicker layer that holds more oil and suits sliding parts, and it usually costs more. Choose by the requirement on the drawing: oil retention and wear call for phosphate, appearance and a thin layer for black oxide.
What should be added to the supplier's price in a quote? Oil if it is not included, masking of seats and holes, a test report, your uplift for risk and capital tied up, transport both ways, preparation and packing, and receiving inspection. In the example in this article they added 76% to the price per kg.
Phosphating and other finishes in QuoteBuddy
QuoteBuddy reads the technical drawing, including the notes, and builds the estimate as separate lines at your own rates. A coating or surface finish called out on the drawing becomes its own operation; QuoteBuddy does not tell phosphating apart from other coatings and finishes, so the line is priced at the rate you set. When it is not one of your in-house capabilities, it is treated as outsourced: priced with your outsourcing uplift, with an outsourcing handling line once per order, and flagged for review until you confirm the step and enter the supplier's hourly rate. The setup minutes, cycle minutes and hourly rate of an operation line can be edited, so the line can match the supplier's real price. See also make or buy for the cost of any outside operation.
You can watch the QuoteBuddy demo video, from technical drawing to quote. To try it on a drawing of your own, start a free 30-day trial.